Just How to Replace a Bathtub
Just How to Replace a Bathtub
Blog Article
Almost everyone maintains his or her own conception about How to Install a Bathtub.
Installing a tub isn't precisely rocket science, however it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a new one is likewise a moderately challenging job. If the old tub is easily available, the job can move rapidly; if you have to open a wall to remove the old bathtub as well as place the new tub, the task is much harder. In either case, the project is within a home handyman's skills, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is much better to think about utilizing one before you begin. Chances are you may need a specialist plumber to make tube links.
This write-up will certainly aid you set up a new tub in your washroom if you have actually currently gotten a new tub and do not require to transform the plan of your previous water system pipes.
Your tools and product list must make up the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is separate the water system. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be quite troublesome due to the limited accessibility that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipes. Once the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washers are in location between the tap and the sink. Secure the faucet in position with the maker supplied backnut. When the tap is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The former type ought to be linked to the faucet finishes first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Utilizing both wood boards under its feet, position the bath tub in the called for placement. The wood boards are practical in equally spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bathtub until the level reviews degree.
To set up taps, fit the bottom of the furthest flexible faucet adapter to the proper supply pipeline by making a compression join; then do the same for the various other faucet.
Turn on the water system and check all joints and also brand-new pipework for leaks and tighten them if necessary. Load the bath tub as well as likewise check the overflow electrical outlet and also the typical outlet for leaks.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been utilized at least when as this will certainly settle it into its last setting.
Preparing for the Setup
Firstly, the sustaining structure provided with the bath should be fitted (if called for) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, causing the water to permeate the wall surface between the bathroom and the tiling, causing complications with moisture and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and also fittings. They are offered in tubes and also cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill the tub with water prior to sealing, to enable the motion experienced when the bathtub is in use. The sealant can break relatively very early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly offered on the marketplace. It is suggested to fit the floor tiles using water-resistant or waterproof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our excerpt on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for taking a few minutes to read our article. Appreciated our blog entry? Please share it. Help another person find it. Thanks a lot for your time spent reading it.
Booking Page Report this page